DTG M2 Step 2 Exam

Your email address:

Your name:

Company name:

When unpacking the M2, you should carefully lift from underneath the bed of the machine.

True

False

Question 1 of 25

What would be a possible issue, if the machine is placed on a folding table (any table that could shake)?

I could spray too much ink on the garment

The image could be out of registration

The print head could hit the garment

There would be no issues

The screws could become loose

Question 2 of 25

You should check to ensure the waste container is in place properly

True

False

Question 3 of 25

Which one of these is not one of the steps in leveling the platens?

Place a jig, such as a few Quarters, in one corner of the platen

Measure from the top of the platen down to the base of the platen

Turn off the gap sensors by pressing the Bed up and Bed down buttons simultaneously

Release the print head

If necessary, adjust the height by adjusting the nuts located under the four corners of the platen

Question 4 of 25

We use the emergency stop button during our routine maintenance of the machine.

True

False

Question 5 of 25

Why would we tip or tilt the waste ink container?

We would never do that, as it could spill ink

To see how much ink is in it

To remove the waste ink container from the machine

Answers B & C above

Question 6 of 25

What is the minimum level, we suggest, you keep your bulk color ink bottles filled?

1/4

1/3

1/2

2/3

3/4

Question 7 of 25

On the WIMS system, you should set the circulating time to 12 – 15 minutes. What should the resting time be set to?

1/2 hour

1 hour

2 hours

3 hours

6 hours

Question 8 of 25

It is suggested to use the Ethernet connection to connect your printer to your computer

True

False

Question 9 of 25

10.

The white ink line connections should be checked, before you put ink in the machine.

True

False

Question 10 of 25

11.

We disconnect the WIMS power supply when we fill the white ink container

True

False

Question 11 of 25

12.

What is the minimum frequency, we suggest you shake the white ink, that is not in the machine?

Once a week

Every other day

We only shake color ink

Two to three times a week

We do not shake any of the inks

Question 12 of 25

13.

There is often residual shipping fluid in the machine, that must be emptied out before filling the machine with ink?

True

False

Question 13 of 25

14.

The color inks can go in any position on the machine?

True

False

Question 14 of 25

15.

Since you may need to do more than one ink charge, how do you know when you are done?

The machine will state: “Ink Charges Completed”

The ink line have ink in them all the way up to the printhead

Ink will be dripping out of the print head

We assume that after performing 4 ink charges, that there is sufficient ink in the system

The ink full sensor alarm will sound off

Question 15 of 25

16.

After doing our ink charge(s), we must do 1 to 2 regular head cleanings, to ensure the print head is primed with ink

True

False

Question 16 of 25

17.

To set the media length, we use a piece of 8 1/2in X 11in paper.

True

False

Question 17 of 25

18.

When you run the first two tick marks (of the media length adjustment) on the paper (provided the machine is not calibrated), it will measure 250mm.

True

False

Question 18 of 25

19.

When setting the media length, it is best to have a metric ruler?

True

False

Question 19 of 25

20.

Before printing each day or doing a nozzle check, it is suggested to do how many head cleanings?

None

One

One to two

Two to three

Four

Question 20 of 25

21.

We initiate a head cleaning by holding down the enter button for three seconds.

True

False

Question 21 of 25

22.

When doing head cleanings, the platen MUST be in a “Loaded” position.

True

False

Question 22 of 25

23.

Nozzle checks are best done on what substrate?

A shirt

A white piece of paper

A black piece of paper

A colored piece of paper

A transparency

Question 23 of 25

24.

We want to see slight breaks in the lines, on a good nozzle check.

True

False

Question 24 of 25

25.

If you have completed 5 sets of 2 head cleanings, each set followed by resting for 15-20 minutes, and then the nozzle checks are not improving, you should contact the support department.

True

False

Question 25 of 25

Loading…